Refurbishing an Antique Ring

Abigail wanted to talk about refurbishing an antique ring. She was new to the area and had recently been proposed to! Her engagement ring was a family heirloom that needed some work.

Abigail had asked for recommendation for a reputable local jeweller on social media, we were thrilled that she had chosen us from the many comments given by local customers!

Jonny had proposed to Abigail with her late Grandmothers ring. It was 18ct yellow gold and set with diamonds and emeralds.

Her Grandmother had loved this ring and Abigail had fond memories of her wearing it a lot. Abigail and Jonny made an appointment at our Shaftesbury Design Studio to talk through the process of refurbishing an antique ring.

The middle emerald had been lost due to the old claws being worn and broken. The two outer emeralds were very worn and looked quite dark in colour, the ring was also more of a square shape than round. Abigail was also keen to have the ring sized to fit her properly – it was slightly too tight.

Louise recommended having the two side emeralds re-polished as they were very scratched and had lost their sparkle, all of the claws needed re-building to be able to hold the gemstones in securely.

Louise showed Abigail a selection of emeralds that would fit her central setting, they agreed to postpone choosing an emerald until the outer ones had been re-polished to get a good match.

Mark carefully un-set her two outer emeralds and gently tapped her ring back to a round shape. The inside of the ring was slightly sharp so he filed this smooth with sandpaper to make it more comfortable.

We re-polished the tops of Abigail’s outer emeralds – you can see the difference this makes to how they shine below! Before they were very scratched and the facets (sides) were almost completely worn away. Re-polishing the tops made them sparkle again!

Mark needed to add a piece of 18ct yellow gold into the band to make Abigail’s ring fit comfortably. He measured the correct size and cut a piece of gold to fit.

Mark used the welder to tac the piece of gold in place, he then placed the solder over the two joins and gently heated the ring until the solder ran into the joins.

It was important to do this sizing job whilst the emeralds were being re-polished and were not in the ring. Emeralds are relatively fragile and don’t tolerate a lot of heat well. It was perfectly fine to leave the diamonds in the ring as they can tolerate higher heat temperatures.

When the new piece of gold was soldered into place, Mark filed this to the same profile as the rest of the band.

He used very fine jewellery files and different grits of sandpaper to shape the new section, and then ensured it was smooth and comfortable when worn.

Abigail returned to our Shaftesbury Design Studio to view a larger selection of emeralds, now that her two outer ones had been re-polished they looked much brighter than before. Abigail hand picked a really bright beautiful emerald to take centre-stage in her engagement ring!

Marcelo built all of her claws up with 18ct yellow gold wire, he was able to do this with the diamonds still in position. Once the claws were the correct length, he expertly set her emeralds in place. After a good clean and polish it was time for Abigail and Jonny to collect their engagement ring!

Abigail and Jonny will soon be having an engagement party with their friends and family! It was our pleasure to restore this family heirloom to it’s former glory and for it to be loved and enjoyed once again!

Come and talk with us about refurbishing an antique ring.

We offer jewellery insurance for the pieces we craft from scratch or refurbish entirely, in partnership with TH March. Click here for more information.

Have a browse through what our customers say about us.

FAQ – Frequently Asked Questions

Can you fix or rebuild a piece that’s this worn or damaged?

Yes — depending on condition, we can either repair specific damage (re-tipping claws, re-soldering joins) or, for pieces that are very worn, fully rebuild them using a 3D scan of the original, resetting your existing stones into the new piece.

Can you size rings to fit?

Yes – we can size rings up or down in size and use a variety of methods to achieve the correct fit for you.

Can I have something similar made?

Yes — every piece we make is bespoke, so we can create something inspired by this story but personalised to you. Book a free consultation and we’ll talk through what’s possible.

How much would a piece like this cost?

It depends on the metal, gemstones, and complexity of the design, so we always provide a personal quote. As a guide, see our Pricing Guide for typical starting prices, or book a free consultation for an accurate quote for your idea.

How long would a piece like this take to make?

Timeframes vary depending on the piece and process involved — typically a few weeks for simpler work, and up to 6–10 weeks for a full bespoke design. We’ll give you an accurate timeframe for your specific piece at your consultation.

How do I get started on a piece like this?

Book a free, no-obligation consultation — in person at our Shaftesbury Design Studio, by video call, or over the phone. We’ll talk through your idea, any gold or gemstones you’d like to use, and what’s possible, before any design work begins.

Book a Private Design Consultation.

Are you ready to have a chat about a jewellery creation? Our private consultations are held free of charge with no obligation to proceed.

We can meet in person at our Shaftesbury Design Studio or via Video Call. We can work via courier service if you are not local to us and have customers all over the UK.

Meet in Person
Book a Call