Family Gold Bracelet, from Father to Son
Ryan had his Dad’s bracelet, his father – Kenneth wanted him to have this and enjoy wearing it. Ryan liked the patterned links but wanted to change the ID part.
He made an appointment with Louise at our Shaftesbury Design Studio to talk about his gents family gold bracelet. He wanted to ask Louise if it was possible to melt the solid ID part and make more links with the gold.



During their conversation, Ryan explained that he worked for a charity in Africa that re-homes elephants who can’t be looked after as pets anymore. Louise couldn’t resist taking before and after photos with one of the wooden elephants from our Design Studio!
Mark is our Master Caster, so this job was one he would take charge of.



Mark removed two whole links from the gents family gold bracelet and attached them to a silver rod. The rod called ‘The Sprue’ and the links are called ‘The Master’. Mark placed the master links and sprue inside of some yellow rubber and heated it until it melted. Once the rubber mould had cooled, he carefully cut it open with a scalpel and released the master and sprue from inside.
The rubber is put back together, then melted blue wax is squirted inside, this cools and is then carefully removed. The wax link is an exact copy of the original gold link.



The wax links are attached by their sprue (- the part where the wax flowed in to the rubber mould), and built up for form a ‘tree’ – the links being the branches. This wax tree is placed inside of a round metal flask. A white substance called ‘investment’ is mixed with water, it forms a paste similar to plaster of paris. This is poured inside of the flask and left to dry out for 24 hours.



The gold bar was placed inside of a crucible and heated by Mark until it started to melt. He used a carbon stick and some flux to clean the impurities from the gold.



Mark carefully removed the hot flask from the kiln, inside the metal flask (tube) is the white substance called investment – and inside of the investment is the blue wax tree (links). In the kiln the wax melts and flows out of the bottom of the flask – it is lost. Hence the name Lost Wax Casting.



With the flask in place, Mark gives the molten gold a good and final blast with the torch to ensure to flows from the crucible into the investment quickly.



When the lid is closed, the crucible and flask spin at high speed and centrifugal force ‘throws’ the molten gold into the investment. It flows into the place where the wax melted out and creates new links inside of the investment.



The flask is left to cool and then the investment is removed; it is plunged into cold water and bubbles away – to leave a gold tree standing proud. You can see this below.



With the gold tree cast, Mark saw-bladed the freshly cast link free from the sprue. Pair by pair, these were removed.



You can see the master below. The original bracelet, plus the newly cast links, plus the links that were used to form the master, now all needed to added back into the bracelet for Ryan.



Mark cut the master links free from their silver sprue and filed all of the cast links smooth.



Every other link was cut and opened up to allow two links to be added to it (one on the left and one on the right).



These links were closed with pliers, next then needed to be soldered closed.



Mark cut small squares of gold solder and placed a square over his original cut on a link. He used the torch to melt the solder and fuse the gold link together. Gold solder is hallmarked – it is the same purity as gold, it is just alloyed with metals that melt faster (at a lower temperature) than gold does.



You can see the small square of gold solder below, then Mark heating it, and finally the soldered link.



Mark assembled the whole bracelet and ensured that all links were soldered together properly.



It was time to give the finished gents family gold bracelet a good polish on our polishing wheel to bring it up to a high sine.



It was a delight to welcome Lucy to our Design Studio to collect this bracelet on her husbands behalf. We hope he enjoys wearing it when he returns from working in Africa.












We offer jewellery insurance for the pieces we craft from scratch or refurbish entirely, in partnership with TH March. Click here for more information.
Have a browse through what our customers say about us.
FAQ – Frequently Asked Questions
Yes – we can mould and cast an identical piece to the one you already have. If your jewellery needs re-furbishing we can re-create it in CAD and then cast a new one, using your own gold or new (recycled).
Yes — casting is ideal for producing single or multiple matching pieces, such as signet rings made for more than one person from the same design.
Yes — every piece we make is bespoke, so we can create something inspired by this story but personalised to you. Book a free consultation and we’ll talk through what’s possible.
It depends on the metal, gemstones, and complexity of the design, so we always provide a personal quote. As a guide, see our Pricing Guide for typical starting prices, or book a free consultation for an accurate quote for your idea.
Timeframes vary depending on the piece and process involved — typically a few weeks for simpler work, and up to 6–10 weeks for a full bespoke design. We’ll give you an accurate timeframe for your specific piece at your consultation.
Book a free, no-obligation consultation — in person at our Shaftesbury Design Studio, by video call, or over the phone. We’ll talk through your idea, any gold or gemstones you’d like to use, and what’s possible, before any design work begins.
Book a Private Design Consultation.
Are you ready to have a chat about a jewellery creation? Our private consultations are held free of charge with no obligation to proceed.
We can meet in person at our Shaftesbury Design Studio or via Video Call. We can work via courier service if you are not local to us and have customers all over the UK.